/*
ROVPS2Control_Masterv8.ino
Hamish Trolove  30 March 2016
www.techmonkeybusiness.com
This sketch takes control commands from a PS2 handset and transmits the
commands using Bill Porter's EasyTransfer Library over a 9600 baud serial
link (100m tether).

This sketch is designed for an Arduino Nano with only one Serial Port.

Pin assignments are:

3.3V output to PS2 red Pin
Pin D10 to PS2 yellow pin
Pin D11 to PS2 orange pin
Pin D12 to PS2 brown pin
Pin D13 to PS2 blue pin

Pin D2 to LED Camera Photo Trigger Indicator
Pin D3 to LED Camera Record Indicator
Pin D4 to LED Main Lights Indicator
Pin D5 to LED ROV Battery Low Voltage Warning
Pin D6 to LED ROV Interior high temperature warning

Communications
Serial Connection: Topside D1 (TX) to ROV D0 (RX)
Serial Connection: Topside D0 (RX) to ROV D1 (TX)
Connect the GND on both

A 16x2 LCD screen is connected as follows
  VSS to GND
  VDD to 5V output of MC78T05CT regulator
  VO to sweep arm of 10kohm variable resistor
  RS to Arduino Nano pin A0
  RW to GND
  E to Arduino Nano pin A1
  D4 to Arduino Nano pin A2
  D5 to Arduino Nano pin A3
  D6 to Arduino Nano pin A4
  D7 to Arduino Nano pin A5
  A to 5V output of MC78T05CT regulator
  K to GND via a 330ohm resistor

5V is supplied from a regulator to the 1Kohm pull up resistors
for PS2 as well as the LCD screen and it's backlight 

The coding pulls on the PSX library developed by Bill Porter.
See www.billporter.info for the latest from Bill Porter and to
download the library.

The controls for the ROV are;
Left Stick - X-axis = Roll, Y-axis = Up/down
Right Stick - X-axis = Yaw, Y-axis = forward/back
Direction button pad left = LED Main lights On/Off toggle
Direction button pad up = turn camera upwards
Direction button pad down = turn camera downwards
Direction button pad right = Change reading on display
Triangle = Start/Stop video recording
Circle = Take photo




*/


#include <PS2X_lib.h> // Bill Porter's PS2 Library
#include <EasyTransfer.h> // Bill Porter's Easy Transfer Library
#include <LiquidCrystal.h>

PS2X ps2x;  //The PS2 Controller Class
EasyTransfer ETin, ETout;  //Create the two Easy transfer Objects for
                            // Two way communication

LiquidCrystal lcd(A0,A1,A2,A3,A4,A5);   //Pins for the LCD display

const int grnLEDpin = 4;  //green LED is on Digital pin 4
const int redLEDpin = 3;  //red LED is on Digital pin 3.
const int yelLEDpin = 2;  //yellow LED is on Digital pin 2
const int VwarnLEDpin = 5;  //Voltage warning LED is on Pin D5
const int TwarnLEDpin = 6;  //ROV temp warning LED is on Pin D6
const int LowBatVolts10 = 96;  //This is for holding the value of the 
                            //Low Battery Voltage warning Voltage threshold x10.

int ForwardVal = 0;  //Value read off the PS2 Right Stick up/down.
int YawLeftVal = 0;  //Value read off the PS2 Right Stick left/right
int UpVal = 0; //Value read off the PS2 Left Stick up/down
int RollLeftVal = 0; // Value read off the PS2 Left Stick left/right
float ROVTMP = 0;  //Variable to hold the converted ROV interior temperature.
int DispOpt = 0; //Variable to signal which value to show on the display 

long PhotoSignalRunTime = 0; //A variable to carry the time since photo triggered.
volatile boolean PhotoActive = false;  // A flag to show that the camera signal has been sent.

struct RECEIVE_DATA_STRUCTURE{
  int BattVolt;  //Battery Voltage message from the ROV.
  int ROVTemp; //ROV interior temperature back from the ROV
  int ROVDepth; //ROV depth reading (m)
  int ROVHDG;  //ROV direction (Degrees)
  int ROVDHTtemp; // DHT11 temperature ***
  int ROVDHThum; //  DHT11 humidity ***
};

struct SEND_DATA_STRUCTURE{
  int upLraw;  //Variables to carry the actual raw data for the ESCs
  int upRraw;
  int HLraw;
  int HRraw;
  int CamPitch; //Angle of the camera servo.
  volatile boolean CamPhotoShot; // Camera photo trigger signal
  volatile boolean CamRec;  //Camera record function toggle
  volatile boolean LEDHdlts; //LED headlights on/off toggle
};

//give a name to the group of data
RECEIVE_DATA_STRUCTURE rxdata;
SEND_DATA_STRUCTURE txdata;

void setup()
{
  ps2x.config_gamepad(13,11,10,12, false, false);
  //setup pins and settings: GamePad(clock, command, attention, data, Pressures?, Rumble?)
  //We have disabled the pressure sensitivity and rumble in this instance and
  //we know the controller type so we have not bothered with the error checks
  pinMode(grnLEDpin, OUTPUT);  //Sets the grnLEDpin to output
  pinMode(redLEDpin, OUTPUT);  //Sets the redLEDpin to output
  pinMode(yelLEDpin, OUTPUT);  //Sets the yelLEDpin to output.
  pinMode(VwarnLEDpin, OUTPUT);  //Sets the low voltage warning pin to output
  pinMode(TwarnLEDpin, OUTPUT);  //Sets the overtemperature warning pin to output.
  txdata.CamRec = false;  //Sets the Camera default to not recording
  txdata.CamPhotoShot = false; //Sets the Camera default to no phototaken
  txdata.CamPitch =90;  //Sets the Camera Pitch to be level
  lcd.begin(16, 2);
  lcd.clear();  //make sure screen is clear.
  lcd.setCursor(0,0);  //Move cursor to top left corner
  lcd.print("Initialising");

  delay(10000);    //The 10 second delay to allow opportunity to upload new programs.
  Serial.begin(9600); //Begin Serial to talk to the Slave Arduino
  ETin.begin(details(rxdata), &Serial); //Get the Easy Transfer Library happening through the Serial
  ETout.begin(details(txdata), &Serial);
  lcd.clear();  //make sure screen is clear again.
  lcd.setCursor(0,0);  //Move cursor to top left corner
  lcd.print("Ready");  

}

void loop()
{
  ps2x.read_gamepad(); //This needs to be called at least once a second
                        // to get data from the controller.
  if(ps2x.Button(PSB_PAD_UP))  //Pressed and held
  {
    txdata.CamPitch = txdata.CamPitch + 2; //increase the camera pitch
  }

  if(ps2x.ButtonPressed(PSB_PAD_LEFT))  //Pressed
  {
    txdata.LEDHdlts = !txdata.LEDHdlts; //Toggle the LED light flag
  }


  if(ps2x.Button(PSB_PAD_DOWN))  //Pressed and Held
  {
    txdata.CamPitch = txdata.CamPitch - 2; //decrease the camera pitch
  }
  txdata.CamPitch = constrain(txdata.CamPitch,20,160);  //Constrain the camera pitch
     //to within range servo can handle.

  if(ps2x.Button(PSB_PAD_RIGHT))  //Pressed and Held
  {
    DispOpt = DispOpt + 1; //step through the data to display.
    if(DispOpt == 2) //At the moment there are only two items of
    //data to display.  This will need to be changed as extra data is added
    //This just resets the data to be displayed to the start of the list.
    {
      DispOpt = 0;
    }
  }

  if(ps2x.ButtonPressed(PSB_GREEN))  //Triangle pressed
  {
    txdata.CamRec = !txdata.CamRec; //Toggle the Camera recording Status
  }


  if(ps2x.ButtonPressed(PSB_RED))  //Circle pressed
  {
    txdata.CamPhotoShot = true;  //Set to indicate photo shot taken.
  }

//Analogue Stick readings
  ForwardVal = ps2x.Analog(PSS_RY);
  YawLeftVal = ps2x.Analog(PSS_RX);
  UpVal = ps2x.Analog(PSS_LY);
  RollLeftVal = ps2x.Analog(PSS_LX);

//Translate the Stick readings to servo instructions
//Readings from PS2 Controller Sticks are from 0 to 255
//with the neutral being 128.  The zero positions are to
//the left for X-axis movements and up for Y-axis movements.

//Variables to carry the actual raw data for the ESCs
  txdata.upLraw = (128-UpVal)-(128-RollLeftVal)/2;  //This will be up to a value of 192 
  txdata.upRraw = (128-UpVal)+(128-RollLeftVal)/2;  //This will be up to a value of 192
  txdata.HLraw = -(128-ForwardVal)+(128-YawLeftVal);  //This will be up to a value of 256
  txdata.HRraw = -(128-ForwardVal)-(128-YawLeftVal);  //This will be up to a value of 256

//Scale the values to be suitable for ESCs and Servos
// These values will be able to be written directly to the ESCs and Servos
  txdata.upLraw=map(txdata.upLraw,-193,193,0,179);
  txdata.upRraw=map(txdata.upRraw,-193,198,0,179);
  txdata.HLraw=map(txdata.HLraw,-256,256,0,179);
  txdata.HRraw=map(txdata.HRraw,-256,256,0,179); 



  // Send the message to the serial port for the ROV Arduino  
   ETout.sendData();

 //Based on Bill Porter's example for the Two Way Easy Transfer Library
 //We will include a loop here to make sure the receive part of the
 //process runs smoothly.
  for(int i=0; i<5; i++){
    ETin.receiveData();

    if(rxdata.BattVolt < LowBatVolts10)  //The factor of 10 is included to 
    // match the factor of 10 used in the reported value which is an int multiplied
    //by 10 to give 0.1 precision to the value.  Make sense?
    {
      digitalWrite(VwarnLEDpin,HIGH);  //If the battery voltage too low,
                                       //trigger the warning LED
    }
    else
    {
      digitalWrite(VwarnLEDpin,LOW);  //Otherwise if voltage above the 
                                      //defined low voltage threshhold
                                      //leave the LED off.
    }
    ROVTMP = (rxdata.ROVTemp * 0.004882814-0.5)*100; //converts the 0-1024 
                                                      //data value into temperature.
    if(ROVTMP > 50)
    {
      digitalWrite(TwarnLEDpin,HIGH);  //If the Interior temp too high (over 50 degC),
                                       //trigger the warning LED
    }
    else
    {
      digitalWrite(TwarnLEDpin,LOW);  //Otherwise if interior temperature within the 
                                      //acceptable level, leave the LED off.
    }

    if(DispOpt == 1) // I think change this number to scroll through //more screens but for this purpose will try to display DHT11 results //on first screen. ***
    {
      lcd.clear();  //A nice clean screen with no remnants from previous
                    //messages.
      lcd.setCursor(0,0); //Top left hand corner ***
      lcd.print("ROV temp:");
      lcd.setCursor(0,1); //Bottom left corner ***
      lcd.print("ROV Humidity:");// ***
      lcd.setCursor(11,0);// 
      lcd.print(ROVDHTtemp); //***
      lcd.setCursor(11,1);
      lcd.print(ROVDHThum); // Display the ROV temperature ***
    }
    else
    {
      lcd.clear();  //A nice clean screen with no remnants from previous
                    //messages.      lcd.setCursor(0,0); //Top left hand corner
      lcd.print("Depth:");
      lcd.setCursor(0,1); //Bottom left corner
      lcd.print("Heading:");
      lcd.setCursor(11,0);
      lcd.print(rxdata.ROVDepth); //Display ROV depth in metres
      lcd.setCursor(11,1);
      lcd.print(rxdata.ROVHDG);  //Display ROV heading in degrees.

    }
    delay(18);
  }

// Signalling the probable status of the camera using LEDs.

  if(txdata.CamPhotoShot && !PhotoActive)
  {
    PhotoSignalRunTime = millis();  //Set the start time for the signal
    digitalWrite(grnLEDpin,HIGH);
    PhotoActive = true;  //record that the photo has been triggered
  }
  if(txdata.CamPhotoShot && PhotoActive && millis() - PhotoSignalRunTime > 2000)  //See if the trigger
 // signal has been running for two seconds
  {
    digitalWrite(grnLEDpin,LOW);
    txdata.CamPhotoShot = false; //Set the camera trigger to off
    PhotoActive = false;  // record that the photosignal has finished.
  }

  digitalWrite(redLEDpin,txdata.CamRec); //Light the redLED based on camera recording status flag
  digitalWrite(yelLEDpin,txdata.LEDHdlts); //Light the LED based on headlights status flag
  delay(18);
}


ROV Arduino Sketch - aka the "Slave"
Again the ROV sketch uses Bill Porter's EasyTransfer library, but other than that it is fairly straightforward. Hopefully the comments will explain it all. 
/*
ROVPS2Control_Slavev8.ino
Hamish Trolove - 30 March 2016
www.techmonkeybusiness.com
This sketch takes commands sent to it from the Master unit with
the PS2 Controller attached and converts it to motor commands,
servo commands, light controls etc.  The data is sent from
the handset (Master) to the ROV(Slave) using Bill Porter's EasyTransfer
Library over a 9600 baud serial link (100m tether).
The MS5803_14 library is from Luke Miller http://github.com/millerlp

Data sent from the Master are raw settings for the ESC control.

This sketch is designed for an Arduino Nano with only one Serial Port.

The pin assignments are;
D13 = RED LED pin.
D12 = Headlight Control
D11 = Jumper pin
D8 = ESC Vertical Left
D7 = ESC Vertical Right
D6 = ESC Horizontal Left
D5 = ESC Horizontal Right
D4 = Camera Pitch Servo
D3 = Video Trigger
D2 = Photo Trigger

A7 = Voltage Divider connection
A6 = TMP36 temperature sensor output pin

i2c bus
GND pins on MS5803-14BA and BMP180 sensors to Nano GND pin
Vcc pins on MS5803-14BA and BMP180 sensors to Nano 3.3V pin
SDA pins on MS5803-14BA and BMP180 sensors to Nano A4 pin 
SCL pins on MS5803-14BA and BMP180 sensors to Nano A5 pin

5V = Supply to the TMP36 temperature sensor.

Communications
Serial Connection: Topside D1 (TX) to ROV D0 (RX)
Serial Connection: Topside D0 (RX) to ROV D1 (TX)
Connect the GND on both

Please note that the ESCs will all have been programmed by this
point in the project.

The onboard voltage, heading, depth, and internal temperature
data is sent through the Serial link back to the Master
for display on a 16x2 LCD screen.

The heading is from an HMC5883L Digital Compass (i2c address 0x1E)
and the depth from a MS5803-14BA high pressure sensor (i2c address 0x76)

See also: HoryzonTrigger.ino, ROVPS2Control_Masterv0.ino,
ROVDoNothing.ino, ROVSubBv0.ino, DigitalCompassv2.ino,
PTLoggerv4.ino and TMP36_Temperature_Sensor.ino.


*/

#include <Wire.h>  //i2c library for the digital compass and depth sensor
#include <Servo.h>
#include <EasyTransfer.h> // Bill Porter's Easy Transfer Library
#include <MS5803_14.h> //Library for the MS5803-14BA
#include <dht.h> // Library for DHT11 sensor ***

EasyTransfer ETin, ETout;  //Create the two Easy transfer Objects for
                            // Two way communication

MS_5803 sensor = MS_5803(512);
#define DHTPIN 9; // Pin used to read the DHT11 sensor ***
#define DHTTYPE DHT11; // Select the type of DHT sensors ***
DHT dht (DHTPIN,DHTTYPE);// ***

Servo ESCVL;  // Create Servo Object ESC Vertical Left
Servo ESCVR;  // Create Servo Object ESC Vertical Right
Servo ESCHL;  // Create Servo Object ESC Horizontal Left
Servo ESCHR;  // Create Servo Object ESC Horizontal Right
Servo CamAng; // Create Servo Object for the Camera Pitch Servo.

const int RedLEDpin = 13; // The indicator LED pin is 13.
const int HeadLts = 12; // The Headlight Control is on pin 12
const int CamRecTrig = 3; //Camera video recorder trigger is on pin D3
const int CamPhotTrig = 2; //Camera photo trigger is on pin D2

const int hmc5883Address = 0x1E; //0011110b, I2C 7bit address for compass
const byte hmc5883ModeRegister = 0x02;
const byte hmcContinuousMode = 0x00;
const byte hmcDataOutputXMSBAddress = 0x03;

volatile boolean CamRecd;  //Camera record function toggle
volatile boolean CamPhoto;  //Camera photo function toggle

const int Voltpin = A7; // analogue pin used to read the battery voltage
const int Temppin = A6; // analogue pin used to read the TMP36 Temp sensor
//Analogue pins A4 and A5 are taken by the i2c bus.


int volts;    // variable to read the voltage from the analog pin
int x,y,z; //triple axis data for the digital compass.
int angle; //calculated horizontal heading angle.

float MS5803Press;  //Pressure from the MS5803 Sensor.
float MS5803Temp;  //Temperature from the MS5803 Sensor.

float DHT11temp; // Temperature from the DHT11 Sensor ***
float DHT11humid;  // Humidity from the DHT11 Sensor ***

const float RefVolts = 5.0; // 5-Volt board reference voltage on Nano
const float ResistFactor = 319.68; //Calculated from 1023.0*(R2/(R1 + R2)
     //where R1 = 2200 ohms and R2 = 1000 ohms for a 15V max voltage.
long TriggerHoldTm = 0;  // the time since the camera button was triggered
long TriggerHoldDuration = 150;  //The time in milliseconds to hold the camera triggers LOW.

struct RECEIVE_DATA_STRUCTURE{
  int upLraw;  //Variables to carry the actual raw data for the ESCs
  int upRraw;
  int HLraw;
  int HRraw;
  int CamPitch; //Angle of the camera servo.
  volatile boolean CamPhotoShot; // Camera photo trigger signal
  volatile boolean CamRec;  //Camera record function toggle
  volatile boolean LEDHdlts; //LED headlights on/off toggle
};

struct SEND_DATA_STRUCTURE{
  int BattVolt;  //Battery Voltage message to the Master.
  int ROVTemp; //ROV interior temperature back to Master
  int ROVDepth; //ROV depth reading (m)
  int ROVHDG;  //ROV direction (Degrees)
  int ROVDHTtemp; // ROV DHT11 temperature to master ***
  int ROVDHThum; //  ROV DHT11 humidity to master    ***

};

//give a name to the group of data
RECEIVE_DATA_STRUCTURE rxdata;
SEND_DATA_STRUCTURE txdata;



void setup()
{
  pinMode(RedLEDpin,OUTPUT);
  pinMode(HeadLts,OUTPUT);
  pinMode(CamRecTrig,OUTPUT);
  pinMode(CamPhotTrig,OUTPUT);

  digitalWrite(HeadLts, LOW); //Set the Headlights to Off
  CamRecd = false;  //Sets the Camera default to not recording
  CamPhoto = false; // No photos triggered.
  digitalWrite(RedLEDpin,LOW);  
  digitalWrite(CamRecTrig,HIGH); //Both camera functions are controlled
  digitalWrite(CamPhotTrig,HIGH); // by making the pin low.

  ESCVL.attach(8,600,2250); //attach the ESCVL to pin 8
  ESCVR.attach(7,600,2250); //attach the ESCVR to pin 7
  ESCHL.attach(6,600,2250); //attach the ESCHL to pin 6
  ESCHR.attach(5,600,2250); //attach the ESCHR to pin 5
    //Due to problems with the ESC recognising the maximum
    //position at the default settings, the figures after
    //the pin number are the microsecond signals for the 
    //minimum and maximum that the ESC will recognise.
    // 600 and 2250 work.
  CamAng.attach(4); //Attach the camera Pitch Servo to pin 4

//  throttle = 90;  //Set throttle to the neutral position.
  ESCVL.write(90);  //Set the ESCVL signal to the neutral position.
  ESCVR.write(90);  //Set the ESCVL signal to the neutral position.
  ESCHL.write(90);  //Set the ESCVL signal to the neutral position.
  ESCHR.write(90);  //Set the ESCVL signal to the neutral position.
  CamAng.write(90); //Set the camera servo pitch to be level.
  
  dht.begin(); // Starts the DHT11 sensor working ***

  Wire.begin(); // Start the i2c communication

  //Initialise the Digital Compass
  Wire.beginTransmission(hmc5883Address);  //Begin communication with compass
  Wire.write(hmc5883ModeRegister);  //select the mode register
  Wire.write(hmcContinuousMode); //continuous measurement mode
  Wire.endTransmission();

  // Initialize the MS5803 sensor. 
  sensor.initializeMS_5803();

  delay(10000);   //Ten second delay
    //The ESC should now be initialised and ready to run.

  Serial.begin(9600); //Begin Serial to talk to the Master Arduino
  ETin.begin(details(rxdata), &Serial); //Get the Easy Transfer Library happening through the Serial
  ETout.begin(details(txdata), &Serial); 


  //The camera starts in record mode probably due to Arduino startup signals
  //and so this needs to be stopped.  The sequence below sends a toggle to
  //the camera to stop it from recording.  obviously this will leave a small
  //waste video file, but we will need to live with that.

  digitalWrite(CamRecTrig,LOW); //Trip the photo trigger.
  delay(100);
  digitalWrite(CamRecTrig,HIGH);

}

void loop()
{
  // Send the message to the serial port for the ROV Arduino  
  ETout.sendData();

 //Based on Bill Porter's example for the Two Way Easy Transfer Library
 //We will include a loop here to make sure the receive part of the
 //process runs smoothly.
  for(int i=0; i<5; i++){
    ETin.receiveData();
    // We'll do something properly with the returned data at a later s
    ESCVL.write(rxdata.upLraw);  //Set the ESCVL signal to the defined throttle position.
    ESCVR.write(rxdata.upRraw);  //Set the ESCVR signal to the defined throttle position.
    ESCHL.write(rxdata.HLraw);  //Set the ESCHL signal to the defined throttle position.
    ESCHR.write(rxdata.HRraw);  //Set the ESCHR signal to the defined throttle position.
    CamAng.write(rxdata.CamPitch); //Set the camera servo pitch to the defined angle.
    digitalWrite(HeadLts,rxdata.LEDHdlts);//Light the headlights based on the Message data
    delay(18);
  }

//The camera settings are status flags so we will need to trigger the events based on
//changes in the data.
  if(rxdata.CamRec && !CamRecd)  //If the signal is to trigger video recording
  //and the Camera is not already triggered drop the camera recording pin to LOW.
  {
    CamRecTrigger(); //Run the camera triggering signal
    CamRecd = true; //update the flag.
  }
  if(!rxdata.CamRec && CamRecd)  //If the camera no longer needing to trigger
  // then signal the camera and turn off the flag.
  {  
    CamRecTrigger(); //Run the camera triggering signal
    CamRecd = false; //update the flag.
  }

  if(rxdata.CamPhotoShot && !CamPhoto)  //If the camera is required to fire a shot trigger
  // the camera photo pin.
  {
    digitalWrite(CamPhotTrig,LOW); //Trip the photo trigger pin.
    TriggerHoldTm = millis();  //Reset the time that a camera trigger was used.
    CamPhoto = true; //update the flag.
  }

  if(!rxdata.CamPhotoShot && CamPhoto)  //If the camera photo signal ceases
  // reset the camera flag.
  {
    CamPhoto = false; //update the flag.
  }  


  if(millis() - TriggerHoldTm > TriggerHoldDuration)  //If camera button held long enough release it.
  // hopefully this little routine will speed up the sketch processing.
  {
    digitalWrite(CamRecTrig,HIGH);
    digitalWrite(CamPhotTrig,HIGH); //Just make them both inactive
  }


  delay(18);  //This delay is added to give the ROV a chance to
                //return data
  volts = analogRead(Voltpin)/ResistFactor*RefVolts*10;  //Read the voltage
  //from the battery through the voltage divider.  Factor of 10 used
  //to help achieve an integer with 0.1V accuracy.
  txdata.BattVolt = volts; //Send back the onboard battery voltage.
  txdata.ROVTemp=analogRead(Temppin); //This reads the pin keeps it as a 0-1024 value.

  //Read the digital compass
  //Tell the HMC5883L where to begin reading the data
  Wire.beginTransmission(hmc5883Address);
  Wire.write(hmcDataOutputXMSBAddress);  //Select register 3, X MSB register
  Wire.endTransmission();

  //Read data from each axis
  Wire.requestFrom(hmc5883Address,6);
  if(6<=Wire.available())
  {
    x = Wire.read()<<8; //X msb
    x |= Wire.read();   //X lsb
    z = Wire.read()<<8; //Z msb
    z |= Wire.read();   //Z lsb
    y = Wire.read()<<8; //Y msb
    y |= Wire.read();   //Y lsb    
  }

  angle = atan2(-y,x)/M_PI*180;
  if (angle < 0)
  {
    angle = angle + 360;
  }
  txdata.ROVHDG = angle;  //ROV direction (Degrees)

  //Reading and MS5803-14BA Sensor
  // Use readSensor() function to get pressure and temperature reading from the MS5803. 
  sensor.readSensor();
  MS5803Press = sensor.pressure();  //Pressure in mbar absolute
  MS5803Temp = sensor.temperature();  //Although we have gathered this
  //it won't be used at this stage.

  DHT11temp = dht.readtemperature();//***
  DHT11humid = dht.readhumidity();//***
  txdata.ROVDHTtemp = DHT11temp;//***
  txdata.ROVDHThum = DHT11humid;//***

  txdata.ROVDepth = (MS5803Press-1013)/98.1; //ROV depth reading (m)

}


void CamRecTrigger()
{
    digitalWrite(CamRecTrig,LOW); //Trip the recorder toggle.
    TriggerHoldTm = millis();  //Reset the time that a camera trigger was used.
}
